Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > Maintenance & Mods (D4)

D4 XS wiring for rear camera
Post Reply  Down to end
Page 19 of 22 <123 ... 1819 202122>
andywillis89
 


Member Since: 15 Oct 2018
Location: Harrogate
Posts: 3

England 2012 Discovery 4 3.0 SDV6 XS Auto Zambezi SilverDiscovery 4

Hi Bodsy, I had a D3 however recently upgraded to a D4, I need to update my profile.
Thanks
Andy
  
Post #20249322nd Feb 2019 10:48 pm
View user's profile Send private message View poster's gallery Reply with quote
Bodsy
Site Sponsor 


Member Since: 06 Nov 2006
Location: In the Clubhouse
Posts: 21361

United Kingdom 2007 Discovery 3 TDV6 HSE Auto Java BlackDiscovery 3

Thumbs Up
 Bodsys Brake Bible

D4/D3 Remote FBH heat kits
BAS Remaps/ EGR Blank
Transmission Flush
Software updates/enabling


Clock/ SNOTM /3Flash / 4x4Info /BT Update /Service Reset/Error Codes / Gearbox Reset
See It Here 
 
Post #20249372nd Feb 2019 11:04 pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
andywillis89
 


Member Since: 15 Oct 2018
Location: Harrogate
Posts: 3

England 2012 Discovery 4 3.0 SDV6 XS Auto Zambezi SilverDiscovery 4

Can any bring me up to speed with who TLO is for the parts?

Thanks
  
Post #20253624th Feb 2019 11:02 am
View user's profile Send private message View poster's gallery Reply with quote
swansty
 


Member Since: 21 Sep 2008
Location: Northern Ireland
Posts: 914

Northern Ireland 2010 Discovery 4 3.0 TDV6 XS Auto Zermatt SilverDiscovery 4

Long retired I believe. try Dan @ duckworths
  
Post #20266288th Feb 2019 11:21 am
View user's profile Send private message View poster's gallery Reply with quote
EIG
 


Member Since: 12 Feb 2009
Location: Enniskillen
Posts: 329

United Kingdom 2015 Discovery 4 3.0 TDV6 SE Tech Auto Loire BlueDiscovery 4

I already have a camera (6-pin), LR051728- which I assume is the CAN bus connected version, fixed camera.

Is this camera suitable for my 2015 D4, if so I would be grateful for help on the part numbers for both the upper and lower tailgate looms. I have been searching on here for that info and although the subject is very well covered I can't seem to find part numbers for looms for this version of camera.

Or is it possible to make up your own cable to run from the camera to the connector at back of the roof.
 Jim

D4 SDV6 SE TECH
2008 D3 TDV6 HSE G4 Challenge Vehicle 
 
Post #205582925th May 2019 12:43 pm
View user's profile Send private message View poster's gallery Reply with quote
l00kin4
 


Member Since: 27 Feb 2015
Location: Sydney
Posts: 46

Australia 2014 Discovery 4 3.0 SDV6 SE Auto Corris GreyDiscovery 4

Hi,

Had a quick look at this and for the fixed CANBUS camera, these should be the looms you need:

LR053163 - lower loom with the switch

LR052996 - upper loom

David
  
Post #205621827th May 2019 4:32 am
View user's profile Send private message View poster's gallery Reply with quote
lrovy
 


Member Since: 30 Apr 2019
Location: Nice
Posts: 88

France 2010 LR4 5.0 V8 HSE Auto Unknown ColourLR4

Hope you can help and advise on best course of action.
LR4 (NAS spec), MY10, HSE and reverse camera flipped the screen (mirrored) and no yellow lines.

It is known issue and described as LR dealer was replacing cameras though I was wondering if it is not a software issue somewhere or if there is any way to fix it? Image doesn't flip just by replacing cables so it was probably a software doing that?

If a replacement is needed, should I go with LR043493 or can the newer LR051728 (CAN based?) be used?

I couldn't see under this thread confirmation on how to get bendy yellow lines. If to get them is only to go for LR051728, does any wiring need to be done?

Or maybe better to go with some aftermarket camera?
  
Post #20665456th Jul 2019 8:20 pm
View user's profile Send private message View poster's gallery Reply with quote
M3bobby
 


Member Since: 21 May 2018
Location: Sleaford, LINCS.
Posts: 857

United Kingdom 

Only a replacement camera will fix this issue.

You need to fit the same camera part number really as the later cameras are totally different. Different connector, different wiring, different fitment etc.

Bendy lines are only on the full surround system. They are driven by the SASM through the camera module.

A generic after market camera in my opinion won’t be as good as OE and will probably involve more work than just replacing your old one.
  
Post #20665817th Jul 2019 7:43 am
View user's profile Send private message View poster's gallery Reply with quote
l00kin4
 


Member Since: 27 Feb 2015
Location: Sydney
Posts: 46

Australia 2014 Discovery 4 3.0 SDV6 SE Auto Corris GreyDiscovery 4

Hi, you can have bendy lines without the full surround system but you do need the Meridian head unit and the CANBUS version of the camera.

David
  
Post #206838815th Jul 2019 6:00 am
View user's profile Send private message View poster's gallery Reply with quote
M3bobby
 


Member Since: 21 May 2018
Location: Sleaford, LINCS.
Posts: 857

United Kingdom 

That will be the 2014 to 2016MY then, the can bus will be needed to communicate with the SASM. I didn’t realise the later standalone camera was CAN BUS. I wonder if Famousfive is reading this?
  
Post #206839315th Jul 2019 6:43 am
View user's profile Send private message View poster's gallery Reply with quote
Famousfive
 


Member Since: 12 Aug 2014
Location: Southampton
Posts: 1806

Ukraine 2013 Discovery 4 3.0 TDV6 GS Auto Loire BlueDiscovery 4

Laughing of course I am .. .but as mine is a MY13 I'm hoping my newly laid coax should be ok ... just 8)

But first to media fix as still not got round to my chores and getting you that part # Very Happy

Cricket and BBQ wiped my car day out yesterday!
 Stolen - D4 Loire Blue
D4 Bali Blue 
 
Post #206840315th Jul 2019 8:59 am
View user's profile Send private message View poster's gallery Reply with quote
lrovy
 


Member Since: 30 Apr 2019
Location: Nice
Posts: 88

France 2010 LR4 5.0 V8 HSE Auto Unknown ColourLR4

l00kin4 wrote:
Hi, you can have bendy lines without the full surround system but you do need the Meridian head unit and the CANBUS version of the camera.

David


That basically means that for MY10 it's a no go... I've HSE with Logic7 (speakers in back pillar, behind 3rd row).
Does the Meridian support that speaker set? What would need to be changed? Even if possible it might be a too big job to be done for just bendy lines, but if it would mean possible navi upgrade that could be a worth while/$$$.

Other option I consider for navi (OT here) is to put some aftermarket android based box and have it functioning under Nav section (GVIFO?) - need to read more and will cover it in separate topic as it is big OT for here. Sorry - just wanted to explain situation around switching to Meridian CAN BUS based camera if possible.
  
Post #206841815th Jul 2019 10:24 am
View user's profile Send private message View poster's gallery Reply with quote
M3bobby
 


Member Since: 21 May 2018
Location: Sleaford, LINCS.
Posts: 857

United Kingdom 

It could be retrofitted to a 2012 on but I don’t think it would work in a 10MY due to the differences in hardware etc.
  
Post #206842915th Jul 2019 12:06 pm
View user's profile Send private message View poster's gallery Reply with quote
J@mes
 


Member Since: 10 Nov 2008
Location: Bomber County
Posts: 4544

England 2014 Discovery 4 3.0 SDV6 XS Auto Corris GreyDiscovery 4

In for later
 2014 D4 XS
2005 D3 SE - Gone 
 
Post #207574713th Aug 2019 1:51 pm
View user's profile Send private message View poster's gallery Reply with quote
NiickJW
 


Member Since: 01 May 2014
Location: Kempsford, Gloucestershire
Posts: 487

United Kingdom 2012 Discovery 4 3.0 SDV6 XS Auto Santorini BlackDiscovery 4

Hopefully picking up my new to me 2012 D4 XS in the next few weeks. Once I get it I'll investigate to see if loom in roof is there, if so this is the first mod I want to do when getting back in a disco. Having read this and other threads I have the part numbers for the switch, loom and camera for the tailgate to start looking for. I saw Wiggs showing a female/female fakra cable for the front. Anyone got a rough length that is needed, looking on eBay and they vary from 0.5M to 5+m? apart from eBay anyone know of a good reasonable price source for all the other parts?

Cheers
Nick
  
Post #219447417th Dec 2020 1:09 pm
View user's profile Send private message View poster's gallery Reply with quote
Display posts from the last:  
Post Reply Back to top
Page 19 of 22 <123 ... 1819 202122>
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site