Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > Technical (D3)

HELP!!! While driving rotational knocking noise.
Post Reply  Down to end
Page 1 of 1
Richie011
 


Member Since: 19 Jan 2018
Location: Elgin
Posts: 2

United Kingdom 2005 Discovery 3 TDV6 S Manual Buckingham BlueDiscovery 3
HELP!!! While driving rotational knocking noise.

Hi folks I'm needing a wee bit of help please.

My D3 had a worn centre bearing on the prop. I started to find I was getting a knocking noise while driving and if I gave it some gas it would turn from a knock to a loud thudding! If you keep the speed steady it would return to just a rotational knocking. So I changed the centre bearing thinking this will fix the problem BUT NO!!! It's like it's trying to get into low drive or like the diff on the front is packing in (I hope not).

Anyone got any magic dust left???
  
Post #190372319th Jan 2018 10:24 pm
View user's profile Send private message View poster's gallery Reply with quote
Randylover
 


Member Since: 31 Jan 2011
Location: Staffordshire
Posts: 1172

United Kingdom 2005 Discovery 3 TDV6 S Manual Zermatt SilverDiscovery 3

Mines doing similar,
My Dual Mass Flywheel is on its last legs

Andy
 05 TDV6,"S" in all colourcoded Zermatt silver,7 seats winter pack HK 6cd stereo,Dual climate,Xenons,

Mods:
Re-Con Engine,De-Tango,Reverse camera,Fog/DRl lights,Aux Battery, perm Aux socket in boot,LED Volt meters in roof panel,Built in tom tom, Strobes fitted in grille, Aux switches for trailer lights fitted in roof panel,Roof Rails,Grille conversion 
 
Post #190380620th Jan 2018 10:54 am
View user's profile Send private message View poster's gallery Reply with quote
Richie011
 


Member Since: 19 Jan 2018
Location: Elgin
Posts: 2

United Kingdom 2005 Discovery 3 TDV6 S Manual Buckingham BlueDiscovery 3

I had the clutch and flywheel done last year I hope it's not that again 🙄.

I find that when I turn left the noise goes away until i have straightened up.

I'm thinking front drive shaft or wheel bearing??
  
Post #190407620th Jan 2018 10:32 pm
View user's profile Send private message View poster's gallery Reply with quote
Globetrotter448
 


Member Since: 21 Mar 2017
Location: Londonderry NSW
Posts: 1783

Australia 2007 Discovery 3 4.0 V6 Petrol SE Auto Java BlackDiscovery 3

When doing the centre bearing did you check the various uni joints. It has often been recommended that you replace the whole prop shaft assembly instead of just the bearing.
I would recheck
  
Post #190415621st Jan 2018 5:29 am
View user's profile Send private message View poster's gallery Reply with quote
L319
 


Member Since: 14 Dec 2013
Location: Herefordshire
Posts: 2080

United Kingdom 2005 Discovery 3 TDV6 HSE Auto Buckingham BlueDiscovery 3

Changed my propshaft as the centre bearing was shot, but when I got it off, found the UJ was also partially seized, have you checked that end as well
  
Post #190417621st Jan 2018 9:33 am
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site