Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > IIDTool Help

IID Tool Error Code Help Needed
Post Reply  Down to end
Page 1 of 1
AlvinR40
 


Member Since: 21 Feb 2023
Location: Coventry
Posts: 3

United Kingdom 2007 Discovery 3 TDV6 HSE Auto Barolo BlackDiscovery 3
IID Tool Error Code Help Needed

Be gentle, the car and IID are new to me, so still learning.

I have just had the torque converter replaced by the garage I got the car from and when I got it back I cleared the codes, took the car for a drive and then read the codes, below is what it is now showing:

L319 - Discovery 3 2008
Vehicle scanned on 22-03-2023 16:31
Using IIDTool BT V3.0 B2803

Engine TDV6
• -UNKNOWN-00 (6C)

Ventilation
• B1B78-84 (2F) System pressure - Bus signal/message failure - signal is below allowable range
( on 22-03-2023 16:16:52 at 150282 mi )

The ventilation one (been there since I've had the car) I think refers to an issue with the heating / air conditioning (quick search on here), could someone please confirm and if this id correct, then what needs to be done to diagnose / repair.

The engine one is new and has only appeared since the torque converter was replaced, can anyone help with this code, as I cannot locate anything when searching.

The tool also shows that some of the ECU's can be updated, are they worth doing or is it a case of not broken so leave well alone?

Thanks in advance
  
Post #233102123rd Mar 2023 1:14 pm
View user's profile Send private message View poster's gallery Reply with quote
SteveNorman
 


Member Since: 14 Oct 2005
Location: Somerset
Posts: 1144

United Kingdom 

Hi,
I think if you update the firmware on the iid tool using the iid tool updater then I expect the engine fault code will have been updated and display the correct fault code.

You other code usually points to low pressure in the air con system. Maybe a leak, or low 134a gas.

regards
Steve
  
Post #233102823rd Mar 2023 2:47 pm
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
AlvinR40
 


Member Since: 21 Feb 2023
Location: Coventry
Posts: 3

United Kingdom 2007 Discovery 3 TDV6 HSE Auto Barolo BlackDiscovery 3

Steve

Thanks for your prompt response

I will give that a go and see if fault gives a better code.

As for the Air Con I'll add that to the list of things the garage need to address.

Regards
Alvin
  
Post #233103523rd Mar 2023 3:57 pm
View user's profile Send private message View poster's gallery Reply with quote
AlvinR40
 


Member Since: 21 Feb 2023
Location: Coventry
Posts: 3

United Kingdom 2007 Discovery 3 TDV6 HSE Auto Barolo BlackDiscovery 3

SteveNorman wrote:
Hi,
I think if you update the firmware on the iid tool using the iid tool updater then I expect the engine fault code will have been updated and display the correct fault code.

You other code usually points to low pressure in the air con system. Maybe a leak, or low 134a gas.

regards
Steve


Steve,

I checked the update for the IID Tool and it is on the latest version.

I will clear the codes and see if the code comes back.

Regards Alvin
  
Post #233164829th Mar 2023 12:07 pm
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site