Member Since: 07 Mar 2009
Location: Clanfield, North of Pompey - UK
Posts: 2686
Lifting the centre console
To save me searching gallery after gallery, does anyone have a link to a set of 'Tips' etc to lifting the the centre console on a D3 Auto.
I'm installing my Parrot Mki9200 this weekend and am hoping to lift it and install the Blue Box underneath.
If nothing else I need to run the CT10LR02 ISO adaptor cable under it to the back of the amp.
I've managed to remove the facia around the head unit etc but can't see how to get the panels around the gear lever, terrain responce controls etc up.
Any help to save me breaking something would be appreciated.
Thanks
Nasher.Heaven doesn't want me, and hell is afraid I'll take over.
14th May 2010 7:38 pm
MacLeod 313
Member Since: 18 Apr 2008
Location: away
Posts: 10723
My Blue Box Here
It is a tight fit, but the cables I found are short, so for me it was the best place I found.
14th May 2010 8:06 pm
Nasher
Member Since: 07 Mar 2009
Location: Clanfield, North of Pompey - UK
Posts: 2686
Thanks Macleod, I did look there first having seen that image before when you posted it.
The Blue box I have appears to be so much larger, it will fit vertically down on the drivers side, and it may well end up there. I do however need to get under the console to run the adaptor cable to the back of the Amp. The bulky ISO connectors between the Parrot cable and adaptor cable also need somewhere to live, and because of the length of the cables have to go under the console.
Plus it appears that at some time somebody has spilt something like hot chocolate or a milkshake all over the centre console as on very close inspection all the gaps are full of it. So I'd like to strip it down and clean it all out.
Nasher.Heaven doesn't want me, and hell is afraid I'll take over.
14th May 2010 8:17 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18454
Member Since: 07 Mar 2009
Location: Clanfield, North of Pompey - UK
Posts: 2686
Thanks Martin
Trouble is it's the initial bit not covered in those instructions that I need first.
ie, how to get the gear knob off, then the Ride height and optimisation panel.
Are those instructions available anywhere I can access them?
Nasher.Heaven doesn't want me, and hell is afraid I'll take over.
14th May 2010 9:17 pm
Dave
Member Since: 08 Mar 2006
Location: North Yorkshire
Posts: 2462
Pull the gear knob upwards quite hard but not so hard you put the sunroof throuh
I don't know the rest thoughCaptain Nick Medhurst would ask:
"What is the first rule when overlanding?"
I would Reply:
"Duratrac"
14th May 2010 10:21 pm
Dave
Member Since: 08 Mar 2006
Location: North Yorkshire
Posts: 2462
Actually I have remebered the rest now.
All the TR and suspension connect via multiple plugs (in a dip under the approximate area of the yellow HDC switch. The panel holding these TR gearstick etc runs all the way from your fridge to your front cupholders and comes off as one (held by approx 6 stiff clips, but don't be scared Of em. I am on my phone so can't link a thread - if you search +console +fitting I think you will find the fridge fitting which details this.
As for getting the "bottom" of the console up - I think that you will find enough space inside, perhaps right at the very front under the area of the ashtraysCaptain Nick Medhurst would ask:
"What is the first rule when overlanding?"
I would Reply:
"Duratrac"
14th May 2010 10:21 pm
Martin Site Admin and Owner
Member Since: 06 Nov 2004
Location: Hook Norton
Posts: 18454
Apply upwards pressure at the front on the TR panel as it's hooked under the trim at the rear. Watch out for the spring clips on the TR panel, check you've got them all once it's off!
For the main console there is usually one only screw used, the one holding the EPB switch in place, the one shown in the PDF on the other side under the rubber tray and plastic insert isn't fitted AFAIK.06 D3 SE / 15 LR D90 XS SW / 88 LR 90 Td5 / 68 BMW 2000 ti
Any issues with the site let me know!
Member Since: 07 Mar 2009
Location: Clanfield, North of Pompey - UK
Posts: 2686
Thanks for the tips and links guys, feel confident I can do it now.
methley wrote:
Why are you going anywhere near the amp?
Because on the logic 7 system thats where the connectors are that the CT10LR02 ISO adaptor cable plugs in to.
It's a Connects2 cable designed that way specifically for the D3(4?) and RRSport.
It saves all the pin swapping that others have had to resort to in the past to get the likes of parrot kits to work with the HK system.
Nasher.Heaven doesn't want me, and hell is afraid I'll take over.
That makes it much more complicated than it really needs to be. I had the console out yesterday and all I had to do was pull the gear lever off, remove the torx screen under the EPB lever and then give a good tug to the plastic on either side. The bit nearest the dash comes off first and then another tug near the armrest cubby does the trick. The wiring can be removed to enable the whole lot to come free but I don't bother.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum