Member Since: 11 May 2006
Location: Off again! :-)
Posts: 72775
Was just thinking about that!
9th Mar 2007 12:23 pm
stapldm
Member Since: 11 Sep 2006
Location: Swine Town
Posts: 2330
Nicely done Wiggs. Dr. Ian Malcolm:
"Yeah, but your scientists were so preoccupied with whether or not they could, they didn't stop to think if they should."
Transgenic tomato anyone?
9th Mar 2007 12:47 pm
STEVEGABS
Member Since: 19 Feb 2007
Location: GABORONE
Posts: 25
Can't see the problem with that. You've still got 3 driven wheels with good tyres and as the car doesn't instantly stop when you get a puncture you will have already driven on it for some distance. Another couple of feet won't hurt in most situations, and in the situations where it will you just go with plan (a), grab the cable and pull the wheel out that way.
It could be worse. With the old Rover P5 the tyre and jack were mounted under the rear floor and if you had a puncture on a rear wheel you didn't have enough clearance to get the jack out......I know it's not considered "kind" to say no these days, but no. Just no, ok? And if it's not ok, still no.
9th Mar 2007 1:23 pm
Baben
Member Since: 15 Feb 2006
Location: Kyalami
Posts: 2059
I tried setting the suspension up to max height before unwinding, then setting it back to access height once unwound, and it worked a treat. It just gives you enough play to pull the spare forward a bit and unhook that stupid mechanism without damaging your arms too much
Granted you probably won't be able to do this in a puddle of mud, but it helps on the road.
My "proper" spare is already in the boot for this weekend in Salisbury with the spacesaver back in the cradle for crumplezone duties. I wouldn't consider going offroad with my only spare hung under the car, that would be asking for trouble!I know it's not considered "kind" to say no these days, but no. Just no, ok? And if it's not ok, still no.
9th Mar 2007 1:33 pm
DiscoDunc
Member Since: 08 May 2006
Location: Bristol
Posts: 16390
Mines on the roof... just about to leave now.... with tintent and fridge full of beer and TwixDuncan
-----------------------------------------------------
If I'd known I was going to be so thirsty this morning I'd have drunk more beer last night.
FFRR Autobiography 4.4 SDV8 MY17
D4 HSE MY13 SOLD
FFRR 3.6 Vogue TDV8 SOLD
D4 HSE MY10 SOLD
D4 SE TECH MY15 SOLD
D4 XS MY12 SOLD
D4 HSE MY10 SOLD
D3 HSE MY06 - Re-Cycled Worldwide
9th Mar 2007 2:09 pm
Calcul@tor
Member Since: 08 Mar 2006
Location: Middle England!
Posts: 810
Re: Spare wheel removal...modification.
wiggs wrote:
Here is the socket , reducer and extension bar . Extension bar has been cut down and welded back together.
You can get different lenghts of extension bar so you may find one the correct lenght (saves cutting and welding)
Can you say what would be the ideal length extension bar?
ThanksD4 XS MY12 Galway
9th Mar 2007 6:37 pm
wiggs
Member Since: 03 Sep 2006
Location: Manchester
Posts: 14368
I can but it would depend on the socket aswell ..you might have a shallow or deep socket!!G4 Gone ...but not forgotten
9th Mar 2007 6:43 pm
wiggs
Member Since: 03 Sep 2006
Location: Manchester
Posts: 14368
Ok , total lenght is aprox 130mm (including socket and bar ).
This is based on an 1/2" drive socket and bar i had originally tryed.
Unfortunaty i have loaded my car back up and its a royal pain in the to unloaded it to check 100%.
I can check for deffo tommorow if it helps after i unload all this.
Unless some one who dosen't have a boot full could measure and check ..just put one seat down and measure from the floor up level with the seat .
Perhaps in hindsight i should of measured in the first place , but hey im only human.
When i know for deffo i will add to the procedure at beginning of this post.G4 Gone ...but not forgotten
9th Mar 2007 6:56 pm
Calcul@tor
Member Since: 08 Mar 2006
Location: Middle England!
Posts: 810
wiggs wrote:
..just put one seat down and measure from the floor up level with the seat .
now why didn't I think of that! D4 XS MY12 Galway
9th Mar 2007 6:59 pm
wiggs
Member Since: 03 Sep 2006
Location: Manchester
Posts: 14368
saying that you will have to measure from inside the plastic shroud that covers the spare wheel bolt ..as it sits slightly lower than the floor.G4 Gone ...but not forgotten
9th Mar 2007 7:01 pm
Desert Traveller
Member Since: 06 Aug 2006
Location: The Gabba - QLD
Posts: 420
For a perfect fit I used
22 x 1/2" socket
3/8"F x 1/2"M adaptor
1/4"F X 3/8"M Adaptor and
1/4" x 75mm extension
The top is flat with the floor and fits between the seats.06 TDV6 SE with many LR and after-market extras. Used only on weekends and trips out west.
Audi TT Roadster (Daily and around town drive)
VW Eos TDI For Sale
Previously 01 TD5 and 94 TDI
2nd Apr 2007 12:17 pm
wiggs
Member Since: 03 Sep 2006
Location: Manchester
Posts: 14368
Did you happen to measure the total lenght of it ..i have not had time to remove all my cr*p and measure it yet !!
I will then add it to my list at the begining of the pageG4 Gone ...but not forgotten
2nd Apr 2007 12:38 pm
chesters
Member Since: 03 Oct 2005
Location: The Toon
Posts: 698
Excelent Idea
Just had the bits come in the post, and done the mod.
I have used,
22 x 1/2" socket
3/8"F x 1/2"M adaptor
1/4"F X 3/8"M Adaptor and
With the height of the three above parts, the seats stop it jumping off the nut head, and I have in my tool kit a 100mm 1/4" extension and tommy bar, that I can slid between the folded seats. This is quite tight but fits great, I was concerned about 1/4" drive undoing a 22mm socket, but it works great.
A 75mm extension was just a bit to short for me, but it all depends on the length of the other three parts, put together.
But a great idea, I will not have to empty the boot again if I get another flat. Arctic Frost Discovery 3 TDV6 SE, Active Rear Diff, Adaptive Head Lights, Tow Pack, Ebony Leather, Roof Rails, Mantec Guard. Tasmod Stainless Sill plates. Grabber AT's. Home made mud flaps. Side Steps back on until the next time.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
to unloaded it to check 100%.
