Advertise on DISCO4.COM
Forum · Gallery · Wiki · Shop · Sponsors
DISCO4.COM > Maintenance & Mods (D3)

Wierd rattle when starting, especially when cold??
Post Reply  Down to end
Page 1 of 1
will.i.am
 


Member Since: 05 May 2016
Location: hertfordshire
Posts: 250

United Kingdom 2006 Discovery 3 TDV6 HSE Auto Keswick GreenDiscovery 3
Wierd rattle when starting, especially when cold??

Hi, i wondered if anyone had any suggestions or help on this?

When starting my disco I get a wierd rattle for the first 1 or 2 revolutions before the engine actually runs, moreso when it is cold. Excuse the terminology but it almosts sounds like the engine is confused as it starts. I am due to get the belts done early decemeber but i wondered if this is something that anyone else has had this and it was anything simple or sinister, in which case should i try and fast track the belts being done?

it is 73k miles and has had a FSH but not knowing what this particular noise is i tohught i would see if any of the more experienced guys on here would be able to share any knowledge?

(I did search for the issue but couldn't see anything come up exactly linking to my issue - its not the EGR tick as this is removed and all blanked and there is nothing mechanial or covers etc that are loose, it is a sound definately coming from the engine.)
  
Post #226409826th Nov 2021 8:17 am
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
john watson
 


Member Since: 10 Nov 2011
Location: lanark
Posts: 955

Scotland 2007 Discovery 3 TDV6 XS Manual Zermatt SilverDiscovery 3

Check that a heat shield has not come loose. Try the rear ones next to the prop shaft. Had a similar problem which went away as the revs increased. The holes holding the shields elongate over time and become loose hence the rattle. When fixed I.e heat shield consigned to the dustbin the car had done about 75000 miles.
 Once you have defeated the idiots any job is half done. Pity there are so many idiots to defeat.  
Post #226410026th Nov 2021 8:28 am
View user's profile Send private message View poster's gallery Reply with quote
will.i.am
 


Member Since: 05 May 2016
Location: hertfordshire
Posts: 250

United Kingdom 2006 Discovery 3 TDV6 HSE Auto Keswick GreenDiscovery 3

Yep ok i will do - i was thinking it sounds more of a metallic engine noise than just a heat shield but thats for your tip, i will have a good look later at the heat shields.
  
Post #226410926th Nov 2021 9:58 am
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
eightfoot
 


Member Since: 12 Apr 2015
Location: sunny essex
Posts: 760

United Kingdom 2005 Discovery 3 TDV6 S Auto Bonatti GreyDiscovery 3

hydrolic cam followers they rattle on startup,supposed to do it tells you in the hand book and does it more when the oil is nice and new (assuming its the right spec)

to confirm stand by the drivers side wheel and get someone to start it when its cold,personally i would be more concerned if it didn't rattle at startup when cold
 please excuse any grammer/punctuation mistakes,i'm thick,thankyou
current vehicles 2005 d3 2013 d4 
 
Post #226411426th Nov 2021 10:15 am
View user's profile Send private message View poster's gallery Reply with quote
will.i.am
 


Member Since: 05 May 2016
Location: hertfordshire
Posts: 250

United Kingdom 2006 Discovery 3 TDV6 HSE Auto Keswick GreenDiscovery 3

v interesting! - this is something i never knew, do youhave a link to it or anything so i can look it up and understand it?
  
Post #226411626th Nov 2021 10:40 am
View user's profile Send private message View poster's gallery Send e-mail Reply with quote
lynalldiscovery
 


Member Since: 22 Dec 2009
Location: Maidstone
Posts: 7274

United Kingdom 2006 Discovery 3 TDV6 Metropolis LE Auto Bonatti GreyDiscovery 3

Hydraulic tappets should not rattle unless they are shagged!
What does rattle on D3 as they age is the camchain tensioners, which have a light spring to hold them in tension, but the engine oil pressure is what keeps them in tension.
So a light tinkling/rattle for a second or two after starting is quite normal, it is not corect but it is common,.
I would hazard a guess that eventually the tensioners will fail, but then mine has been tinkling on start up for the best part of 7 years!

But I do not think this is your noise as you say the noise happens before the engine starts, and if you can hear the camchain rattling beofre you sart you could be in trouble.
  
Post #226415726th Nov 2021 5:29 pm
View user's profile Send private message View poster's gallery Reply with quote
eightfoot
 


Member Since: 12 Apr 2015
Location: sunny essex
Posts: 760

United Kingdom 2005 Discovery 3 TDV6 S Auto Bonatti GreyDiscovery 3

read the handbook it says normal operation nothing to worry about Thumbs Up
 please excuse any grammer/punctuation mistakes,i'm thick,thankyou
current vehicles 2005 d3 2013 d4 
 
Post #226418426th Nov 2021 7:41 pm
View user's profile Send private message View poster's gallery Reply with quote
PROFSR G
 


Member Since: 06 Mar 2017
Location: Lost
Posts: 4581

Ukraine 2009 Discovery 3 TDV6 Commercial XS Auto Stornoway GreyDiscovery 3

The handbook is wrong if it says rattling cam followers is normal, and rattling timing chains as a result of poor oil pressure/worn tensioners is not normal engine behaviour either.

And, if they rattle for anymore than 3 or 4 seconds you should be worried as the above is a major contributor to their snapping. Thumbs Up
 yµ (idµ - eAµ) ψ=mψ

 
 
Post #226419026th Nov 2021 8:34 pm
View user's profile Send private message View poster's gallery Reply with quote
lynalldiscovery
 


Member Since: 22 Dec 2009
Location: Maidstone
Posts: 7274

United Kingdom 2006 Discovery 3 TDV6 Metropolis LE Auto Bonatti GreyDiscovery 3

eightfoot wrote:
read the handbook it says normal operation nothing to worry about Thumbs Up


This just goes to show that men dont read the instruction manual, they incl me all think you are wrong, but we are to lazy/disinterested to bother looking Mr. Green

But if you post which page/section it is in I may take a look out of curio?
  
Post #226422727th Nov 2021 7:42 am
View user's profile Send private message View poster's gallery Post Reply
Display posts from the last:  
Post Reply Back to top
Page 1 of 1
Jump to:  
Previous Topic | Next Topic >


Posting Rules
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum



DISCO4.COM Copyright © 2004-2024 Futuranet Ltd & Martin Lewis
DISCO3.CO.UK RSS Feed - All Forums

DISCO4.COM is independent and not affiliated to Land Rover.
Switch to Mobile Site