Martin
Site Admin and Owner
Member Since: 06 Nov 2004
Location: Warwick
Posts: 10481
  
|
| Park Distance Control fails |
|
- Classification
- Fault - electrical/software
- Problem
- Front PDC does not activate when reverse then move straight to D – requires a very definite “stop”
- Affected vehicles
- PDC-equipped
- Reported Cases
- Many
- Occurs
- Always (if move off after reversing)
- Submitted to dealer network
- Yes
- Dealer Response
- None
- Submitted to LR Customer Services
- Yes
- LR CS Response Reported
- Will liaise with dealer
- Fix/Solution
- Technical Service Bulletin number LA413-001 contains a fix for the problem. Quote the TSB number to your dealer.
- Other Comments
- None
Last edited by Martin on Mon Jan 02 2006 11:50am. Edited 1 time in total
|
 Sun Feb 06 2005 12:22am |
|
|
Ecosse
Member Since: 07 Jan 2005
Location: Grampian, Scotland
Posts: 753
|
LR advise that it requires to be static when moving into D!! However I hae discovered that from parked, start up & go straight to D then move off & it does not ativate - it only comes on if you "stop" ie you have to ove off & then stop!! - not much use if getting out of a tight parking space & want to move forward first!
|
| Wed Feb 23 2005 11:35pm |
|
|
kjh1957
Member Since: 05 Nov 2005
Location: Northamptonshire
Posts: 43
|
I had the same problem but having taken it back to the dealer (when my suspension compressor failed) they managed to rectify the problem. Apparently it needs a new 'module'.
It works a treat now.
|
| Sat Nov 05 2005 5:08pm |
|
|
Gareth
Site Moderator
Member Since: 07 Dec 2004
Location: Bramhall
Posts: 15750
 
|
Yes, I think Martin you should ammend this issue as "Fixed" and put the Technical Service Bulletin number on. TSB Ref. no No.LA413-001, on Land Rover GTR now. I have had this done and it is great. Club 18 - 30 (I wish !!)
|
| Sat Nov 05 2005 6:58pm |
|
|
Martin
Site Admin and Owner
Member Since: 06 Nov 2004
Location: Warwick
Posts: 10481
|
Issue updated and tagged as solved  06 D3 SE / 04 Mini JCW / 68 BMW 2000 ti
Any issues with the site let me know!
Go shopping for stickers, hi vis vests, sat-nav video input cables, new style FBH terminals, clothing, key rings and more
|
| Mon Jan 02 2006 11:50am |
|
|
pete571
Member Since: 13 Jan 2009
Location: notts
Posts: 6
|
The rear park sensors require the handbrake to be applied first, select reverse in manual then disengage h/b, otherwise the system does not work! Hence, I crumpled my bumper relying upon the warning beeps!
LR dealer had it for a good day before discovering this and reported back to LR
Nov 2004 D3 pete57
|
| Wed Jan 14 2009 5:29pm |
|
|
PaulnhisGirls
Member Since: 17 Nov 2006
Location: Chester
Posts: 127
|
Tallulah is an 06 manual and the sensors worked a treat up until about a month ago! 70k with only the occassional blonde moment when confused by a bus, wagon or motorbike exhaust note, but now she screams like a good one nearly ever time I select first? And screams until we're above 5mph? Any ideas?
|
| Wed Apr 15 2009 7:01pm |
|
|
NoDo$h
Member Since: 02 May 2006
Location: almost on the Piddle
Posts: 13093
|
One of the sensors has a short, either in the cable or through damp entering the sensor head itself. You cannot begin to comprehend the immensity of the  I do not give.
|
| Wed Apr 15 2009 9:53pm |
|
|
wvlenthe
Member Since: 07 Jan 2009
Location: Arnhem
Posts: 1169
|
I just had the same fixed; dealer told me one of the connectors had loosened. May be worth a check before going to dealers?
Wiljo Two D3 V8 HSE Auto in Zermatt silver - one for the driveway, one for the living room cupboard.
|
| Thu Apr 16 2009 7:11pm |
|
|
wilsonmg
Member Since: 16 Apr 2008
Location: Wigan
Posts: 334
|
Slightly different issue has just appeared.......
when I select reverse, I get a higher than usual 'beep', that is constant for about 5 sec's, then stops then the amber PDC light starts to flash ?????
the front sensors are still fine and work ok... only the rear ones having a hissy fit..... anyone any idea's  Baby RR
MX5 Mk1 (supercharged)
Still miss my D3 
|
| Tue May 05 2009 11:32am |
|
|
Dickydisco
Member Since: 03 Feb 2009
Location: Somewhere on the Trent
Posts: 435
|
I went to look at a Discovery today. I tried to use the rear PDC. I reversed up close to a wall and they did nothing, no noise at all from them. I even tried pressing the button on the dash but still nothing. It had no light on the button but not owning a disco yet im not sure if there was somthing I should have done. I am going to have the car but if its not fixed before I get it then I want some heads up. Any help would be great. Ive searched for threads on this but none help.
Cheers guys
|
| Sun Jul 26 2009 10:47pm |
|
|
ad15
Member Since: 14 Dec 2008
Location: up that tree
Posts: 4852
|
was it manual or auto? one wife.......livid
|
| Sun Jul 26 2009 10:54pm |
|
|
Dickydisco
Member Since: 03 Feb 2009
Location: Somewhere on the Trent
Posts: 435
|
Its a manual
|
| Sun Jul 26 2009 11:11pm |
|
|
ad15
Member Since: 14 Dec 2008
Location: up that tree
Posts: 4852
|
ok mine does the same, PDC only engages if the handbrake is off and you select reverse,,,, try it a few difrerent ways,, does it not work in any configuration?
it's annoying that it doesnt just work... but it is a landrover after all and life just aint that simple.... one wife.......livid
|
| Sun Jul 26 2009 11:42pm |
|
|
Dickydisco
Member Since: 03 Feb 2009
Location: Somewhere on the Trent
Posts: 435
|
Well Ad, Iv tried it with no handbrake but not with. I pulled past wall then right into reverse to back up to it, no handbrake and pretty much no pause between forward and reverse. I get the feeling the car may have been used to launch a boat, dont know if it is fresh or sea water. Are they prone to water damage?
|
| Mon Jul 27 2009 12:06am |
|
|
